The tense position of fiber laser cutting machine in cutting pipe industry
The fiber laser cutting machine is about multi-tube-one-plate intersecting grooves, so the mathematical model of tube-tube or tube-plate intersecting is realized by cutting repeatedly, with low manufacturing compliance and high waste rate, because of the reality in engineering The existence of the complexity of multi-tube and one-plate intersecting requires a question of forming intersecting grooves. Based on the established mathematical model and the proposed intersection algorithm, this article conducts a kinetic analysis of the cutting torch path of the active fiber laser cutting machine. .
Establishment of the optical fiber laser cutting machine's trajectory, the relevant shape and mathematical model, the cut tube is connected, and the cutting machine body realizes all the actions of the cutting process, that is, the cutting torch edge The pipe to be cut has three-axis linkage and one-axis manual operation. Its action is related to the following: Before the formal cutting, the cutting torch moves along the radial direction of the cut pipe to adjust the position of the cutting torch compared to the cut pipe. This matter is controlled by the operator, that is, manually. After the formal cutting, according to the various parameters that have been adjusted, the cutting torch actively realizes the whole cutting process, that is, the cutting torch requests to move around the pipe to be cut according to the set rate, and at the same time, the cutting torch is along the axis of the pipe to be cut. For axial movement, the speed is determined by the thickness of the cutting board and the reversal speed of the cutting torch.
There are multiple intersecting modes such as tube-to-tube intersecting, tube-to-plate intersecting, or multi-tube intersecting. Therefore, it should be possible to establish a mathematical model of response based on the different coherence patterns.
How to improve the operating rate of the active fiber laser cutting machine
The workpiece is not twisted, the noise is small, and the compliance is high during the homework of the full-active fiber laser cutting machine. However, when the pipe diameter is large, the saw blade increases with the increase of the pipe diameter, and the cutting material faces the middle inclination, parallelism and other appearance quality will be worse, and the material will be lost during machine processing. When the blank is blank, there is always a small piece of front blank on one wall, which not only affects the positioning of the next process, but also scratches the hand.
In response to these questions, our company has made new innovations to better improve the operating rate of the active fiber laser cutting machine, and reduce the raw materials and a large number of tasks. Lower the old cost.
The application of dynamic fiber laser cutting machine in ordinary manufacturing is still increasing. It can be seen that the benefits of fiber laser cutting machine application occupy an important position, and lathes are fully active. The workpiece is twisted during the homework of the fiber laser cutting machine, and the cutting material faces the middle inclination, parallelism and other appearance quality can reach very aspirational conditions, but the cutting obedience is low, the noise is exceptionally large, the chip is very long and not easy to break, and the tool life is short.
Operation analysis of fully active stainless steel fiber laser cutting machine
Installation of fiber laser cutting machine: The fiber laser cutting machine must be placed flat on the painted cement On the ground, it is also very good to follow the screw holes in the four corners of the fiber laser cutting machine base to keep the fiber laser cutting machine on the ground. Continuous power cable: The fiber laser cutting machine itself has been connected to the power line in advance, and the only thing to do is to follow your local power safety regulations to connect the external cable of the fiber laser cutting machine to the power supply box without melting Wire switch. At the same time, note that the outer cable is 4 wires, and the ground wire should be connected to the grounding discussion point.
Reminder: Check whether the VOLTAGES provided by the power supply is the same as the label on the machine. If it is not, please do not connect the power.
Continuously shrinking atmosphere tube: The supply source of the shrinking atmosphere must be connected to 6-8BAR (90-IISPSL) to set the shrinking atmosphere to T. D. After connecting the 5/1 air pressure pipe to the base of the machine, the female end can be quickly discussed.
Try the pace
1. Turn on the power switch controlled by the main fiber laser cutting machine.
2. Press the manual button on the panel; the spindle rolls immediately; pay attention to see if the spindle rolls counterclockwise, (the same direction as the guide on the safety cover of the saw blade) If not, please shrink the power box switch and replace any two lines that the switch continues Continue, turn on the switch again, and try again at the above steps.