Teach you how to install fiber laser cutting machine
1. The fiber laser cutting machine is placed on a horizontally painted cement ground, and the fiber laser cutting machine can be fixed on the ground according to the screw holes located in the four corners of the base of the fiber laser cutting machine.
2. Then hold the tail power cable, in the fiber laser cutting machine itself, the power line is usually connected in advance, so the assembly is based on the demand The relevant safety laws and regulations of your electricity power connect the external cable left by the fiber laser cutting machine to the non-fuse switch of the power supply box. It should be noted that the external cable has 4 wires, and these are all connected to the ground wire. Go to the Tongdi Discussion Office.
3. The bottom is the need to check whether the volts provided by the power supply has been the same as that of the machine. If it is not, please do not connect it.
4. Then, it is necessary to connect the shrinking atmosphere supply source of the tail shrinking atmosphere tube to the fast discussion female end after connecting the shrinking atmosphere air pressure tube to the machine base. Yes, test the motor steering.
Analysis of the placement of fiber laser cutting machine
1. After the pusher is used to push to the placement position, gently put it down , Do not fall or violently collide.
2. Use the spirit level to adjust the machine to a level position.
3. Be sure to connect the green bottom line to avoid dangers caused by electricity.
4. Connect the power cord, please connect the non-fuse switch or the knife switch, pay attention to the lack of phase, so that the motor can not be started and destroyed. After starting the motor, check whether the running direction is similar to the scarlet arrow on the saw blade cover. If the rotating shafts are inconsistent, swap the two power cables. Note that the green ground wires cannot be interchanged.
5. Note that it is impossible to change speed during the sawing process. If you need to change speed, first turn off the spindle and wait for the spindle to stop completely before changing the speed, saving the motor or spindle head The gears run upside down and cause damage.
6. Set the saw blade according to the blood-colored arrow on the saw blade cover. It is not possible to reverse the installation of the saw blade to avoid the danger of saw blade fragmentation. Lock the saw blade to lock the bolt in the opposite direction of the red arrow. It is determined that the saw blade has been locked and will not loosen before the spindle can be started. The loose saw blade will be maintained and protected from chipping during sawing and causing danger
What questions should be paid attention to during the operation of fiber laser cutting machine
When it comes to fiber laser cutting machine, friends may think that it is very strange . However, we have seen a few bends in our lives, and these bends can be said to be a product under the fiber laser cutting machine.
Fiber laser cutting machine can be roughly divided into CNC fiber laser cutting machine, hydraulic fiber laser cutting machine and so on. It is mainly used in electric power construction, highway and railway construction, steam boilers, bridges, ships, furniture, decoration and other aspects of pipeline laying and repairing. It has the advantages of multiple functions, reasonable layout, and simple operation.
The fiber laser cutting machine factories manufactured by know that there are many varieties of fiber laser cutting machines, which are divided into bending type, roll bending type, surrounding type and Extrusion type, etc.; according to whether it is heated during winding, it can be divided into two types: bending type and hot bending type; according to the difference of transmission method, it can be divided into machine transmission and hydraulic transmission.
Attention should be paid when operating the fiber laser cutting machine.
1. When the machine tool is started, pay attention to the limitation that the human body cannot come in and the rotating arm twists and sweeps. When working on the machine tool, all staff are not allowed to come in and the limited space swept by the boom and pipe fittings. The machine tool hydraulic system adopts YA-N32 general hydraulic oil, which is changed once a year under normal conditions. The oil filter must be flushed at the same time.
2. When mediating the mold, the mediator should press the button to mediate. It is absolutely impossible for one person to mediate on the machine tool and the other person to control the cabinet. When mediating the machine tool or driving an empty car, it should be unloaded. Core rod. The hydraulic system also needs to pay attention to the pressure in the operation.
3. Otherwise, it is forbidden to push the side pushing speed higher than the linear speed of twisting the edge of the mold under manual conditions. Generally, after a period of time, the machine should check the tension level of the chain, and the tension of the high and low chains should be equal.
4. In active maneuvering in the winding mode with core, before the bending arm is retracted, the operator must wrap the core head in the tube, or ensure that the mandrel does not intercept signs when the bending arm is retracted, so as to save the core The head or core rod is bent or broken.