Specific operation steps of automatic fiber cutting machine

Taiwan group automatic fiber cutting machine linkage mode: turn the selector switch to the position, press the beam forward button, then the beam will continue to move forward, until the forward limit switch is activated or the STOP button is pressed, the beam will stop moving; press it once The beam back button. At this time, the beam keeps backing until the limit switch is activated or the STOP button is pressed. Training is allowed only after obtaining the corresponding qualifications, and it is strictly forbidden to work without a certificate. Infrared bridge cutting table group automatic fiber cutting machine operators must be familiar with the main performance and operation methods of the machine tool, size input method, various functional indicators and common troubleshooting, and do the daily maintenance of the machine tool. Check before starting to check whether the power supply and cooling system are in normal working condition. Check whether the hydraulic system is working properly, the hydraulic oil is sufficient, the oil pressure is correct, and there is no leakage. Check whether the saw blade model is consistent with the stone to be cut; whether the installation and rotation of the saw blade meet the specified requirements, and whether the blade is sharp. Check that the walking part of the cutting machine is free of obstacles. If there is, it should be removed in time. Check whether the rotary positioning of the worktable is accurate. Check whether the boom is working normally, whether the jaws are flexible, and whether the clamping force is sufficient. After receiving the processing order, the cutting machine must see all the content contained in it and understand it thoroughly. If there is any objection, it should be raised immediately, and the cutting board can be turned on after the resolution is resolved. Check and verify whether the variety and quantity of the plates transferred to the machine are consistent with the processing list. Whether there is too much quality problem, and make detailed records. If there is any objection, it should be reported and dealt with in time. Before processing the large slabs, check the specifications and dimensions to see if they are made of material. If the difference is too far, they should be reported to the workshop technicians in time, and the knife can be used to cut the slabs after an affirmative answer. The layout of the boards should be reasonable during processing, so that each large board and slab trimmed must achieve a higher yield rate.

In case of defects such as color bladder, chromatic aberration, cracks, etc., the Taiwan-group automatic fiber cutting machine should be as far away as possible without affecting the yield rate. If the customer has Special requirements or clear provisions on the processing order should be handled as required. When processing fragile plates, when the large slab is hoisted on the machine, the foot rest of the machine must be lined with wooden boards. Generally, single-piece hoisting is not allowed. In the process of processing, granite single-side processing marble can process two large slabs at the same time when using a 400-size saw blade. When the cutting machine enters the working state, the operator should concentrate and pay attention to observation. The knife should be advanced at the most economical and effective speed, the knife stroke should be accurate, and the distance of the empty knife should be minimized. The ideal reference value is around 20 for granite and around 30 for marble. The specific operation should be adjusted according to the cutter, plate hardness and thickness, and the situation such as strict explosion-proof edge, moving plate and failure to completely or not fully automatic fiber cutting machine for slate group. For Taiwan-group automatic fiber cutting machine, the size must be re-checked after the second knife is completed, and the size must be re-checked after the second knife after the machine is turned. The error must not exceed ±0.5mm, and the diagonal deviation must not exceed 0.3mm . In case of breaks, missing corners, etc., the broken blocks, fragments, etc. should be picked up and placed in the designated place for repair according to the requirements. The finished boards of the group of automatic fiber cutting machines should be checked for specifications and quantities according to the processing sheet, and the size should be marked and labeled. If there are several processes, the boards should be classified and stacked neatly in the designated place according to the regulations, so as to minimize the handling workload and reduce unnecessary damage caused by multiple handling, while facilitating shipment. When handling the processed specification boards, strictly abide by the 'Safety Operation Regulations for Handling'. Be strict when processing on behalf of customers, and should respect the customer's layout method. If there is any objection, it should be patiently explained to the customer. If the customer insists, the customer's opinion shall prevail.