Some points to see when using fiber laser cutting machine

The must-see points for the use of fiber laser cutting machine

1. The function of the equipment must be checked carefully before application, and the integrity of each component must be connected.

2. The power switch, the tightness of the saw blade, the saw blade guard or the safety baffle are carefully checked, the front desk must be stable when driving the cutting, and there should be sufficient illumination during night homework .

3. Before application, turn on the main switch first, test it for a few laps without load, and allow it to start after confirming that it is safe and sound. Before driving, it is necessary to check whether the power supply is consistent with the general rated 220VA voltage on the power switch, so as to avoid wrong connection to the 380VA power supply.

Some points before using the fiber laser cutting machine

1. The driver must be familiar with the layout, function, driving system, transmission system, protective assembly, smooth parts, electrical Basic common sense and application skills.

2. Before boarding the machine, wear protective equipment for the task as prescribed. The female worker must press her hair into the working cap. It is strictly forbidden to wear gloves, scarf, and apron when cutting.

3. Before driving, check the position of the handles, the transmission parts and the protective cover, the limit assembly should be firm and reliable, whether the tool is reliable, whether the cutting fluid meets the requirements, and the electrical guard is reliable, etc. . After the inspection, according to the parts and oil volume delineated by the smooth chart of this machine tool, smoothly refuel before the shift.

4. After checking and refueling, the driver drove at a low speed and idling for 3~5 minutes, and checked whether the machine tool was running very loudly, the smooth environment of all parts, the smooth oil level environment, and whether the control handle was naive. Check whether the mechanism is up to 2/4 is always reliable, whether the machine and electrical limits are reliable, whether there are cracks in the tool and grinding wheel. Arrange the time span. The grinding wheel must be changed before the one-month grinding wheel cutting machine is used.

5. When processing and driving, the energy must be intensive, and it is strictly forbidden to speak with others. It is strictly forbidden to leave the job while actively moving the knife; it is strictly forbidden to use the side of the grinding wheel cutter to polish the burrs; it is forbidden to exceed the standard application; it is forbidden to remove the machine and the electrical limit at will; it is forbidden to arrange excess items at the work station; it is forbidden to install excess equipment; it is forbidden to use rope or wire Tie the handle to control processing. The vehicle must be parked when leaving the machine tool, and the power supply should be turned off when the time is long.

6. The tool clamping is flat, reliable, and check for looseness at any time.

7. Before processing, it is necessary to test the distance in an empty car, and the processing can only be carried out after the distance limit of the coming and going distance is determined to be correct.

8. When clamping a workpiece, a suitable and safe clamping method must be selected according to the material type. The workpiece must be perpendicular to the cutting line of the tool, must be fastened and reliable, and long materials must be supported by a special bracket.

9. When cutting first, it is necessary to investigate whether the code word is deviated. When excavating the deflection, the vehicle must be parked immediately to prevent the knife or grinding wheel from rotating and breaking.

10. In business, the driver must stand on the side of the cutting tool and the grinding wheel, guard against the tool, workpiece, the future, the demand for doubled products, doubled intelligent objects, and respond more quickly to environmental trends. We demand that our target can promote the management level of the enterprise, and the diligent and thrifty enterprise can produce the capital.

Under the fiber laser cutting machine, let me explain the functions and features of Radan software. As a professional sheet metal planning and processing system under Vero, Radan provides users with comprehensive sheet metal processing plans such as product planning, layout planning, programming assistance, and production management. Radan can realize 2D drawing, 3D sheet metal modeling, 3D mold active opening, nesting plan, cutting programming, stamping programming, bending machine programming and simulation. In addition, it also provides functions such as drawing and document management, DNC French transmission, sheet metal production information management system, etc., which can almost cover all the functions of sheet metal production from planning to processing to management. Radraft is a drawing software designed for sheet metal. Its drawing method is completely different from that of engineering software. Compared with the ancient manual nesting, Radan completely automates the nesting. The planner only needs to input the graphics of the parts to be nested, and the system can automatically sort and nest parts according to the part styles, producing very reasonable nesting results; the nesting plan is subject to double progress; at the same time, it can achieve a little artificial basis. The complicated nesting plan.