Safety operation regulations
Before processing, the automatic optical fiber cutting machine of the group of stations must test the stroke in an empty vehicle, and the processing can be carried out after confirming that the reciprocating stroke limit work is correct. When clamping the workpiece, a suitable and safe clamping method must be selected according to the material type. The workpiece must be horizontal and vertical to the cutting line of the tool, and must be fastened and reliable. Long materials must be supported by a special bracket. When starting to cut, you must observe whether the incision is skewed, and you must stop immediately when it is found to be skewed to prevent the cutter or the grinding wheel from twisting and breaking and hurting people. When working, the operator must stand on the side of the cutting direction of the tool and the grinding wheel to prevent the safe operation of the tool, workpiece, and metal cutting machine. Purpose In order for the operator to be able to regulate the operation at work, learn the safe operation rules, master the safe operation technology, and avoid safety accidents. happened. In the daily maintenance and daily inspection, the bow saw machine, the grinding wheel cutting machine, the pipe thread cutting machine, the metal circular saw machine, the metal band saw machine, etc. are used in the daily inspection. Management Responsibilities/Post Responsibilities and Authorities Engineering Equipment Department Engineering and Equipment Department Engineering is responsible for the safety matters of construction within the jurisdiction. The work requirements for the quality of the construction within the jurisdiction are responsible for the work requirements/management and control points. The performance of the equipment must be carefully checked before use, and the various items must be maintained. Integrity of components. The power switch, the tightness of the saw blade, the saw blade guard or the safety baffle shall be inspected in detail. The front desk of the operation cutting must be stable, and there should be sufficient lighting brightness during night operation. Before you are ready to use, turn on the main switch and make a few rounds of no-load test. After confirming that it is safe and correct, it is allowed to start. Before operation, you must check whether the power supply is consistent with the conventional rated 220VA voltage on the power tool, so as not to connect it to the 380VA power supply by mistake. The operator must be familiar with the structure, performance, operating system, transmission system, protective device, lubrication parts, electrical and other basic knowledge and usage methods of this machine tool.
Wear the labor protection equipment according to the regulations before the operation of the Taiwan-group automatic fiber cutting machine when cutting, and the female worker must press the hair into the work cap. Note that it is strictly prohibited to wear gloves, a scarf, and apron. Before starting the project, check the positions of the handles, the transmission parts, the protective cover, and the limit device should be firm and reliable, whether the tool is firm and reliable, whether the cutting fluid meets the requirements, and the electrical protection is reliable. After inspection, perform pre-shift lubrication and refueling according to the parts and oil quantity specified in the machine's lubrication chart. 2/4 Group review version, Word can be edited to check and after refueling, the operator drives at low speed and idling for 3~5 minutes to check whether the machine tool is running for abnormal noise, lubrication of various parts, lubricating oil level, whether the joystick is flexible, and the reciprocating mechanism Whether it is normal and reliable, whether the mechanical and electrical limits are reliable, whether there are cracks in the tool and the grinding wheel. The grinding wheel must be replaced before the grinding wheel cutting machine is used for more than one month. When processing, you must concentrate, and it is strictly forbidden to talk to others. It is strictly forbidden to leave the post when the knife is automatically moved; it is strictly forbidden to polish the burrs on the side of the grinding wheel cutting machine; it is not allowed to use beyond the specification; it is not allowed to remove the mechanical and electrical limits at will; it is not allowed to place extra items on the workbench; Use rope or wire bolt handles for manipulation and processing. You must stop when you leave the machine tool, and turn off the power when it takes a long time. The tool clamping is flat, firm and reliable, and check for looseness at any time. Before processing, it is necessary to test the stroke in an empty vehicle, and the processing can only be carried out after confirming that the reciprocating stroke limit work is correct. When clamping the workpiece, a suitable and safe clamping method must be selected according to the material type. The workpiece must be horizontal and vertical to the cutting line of the tool, and must be fastened and reliable. Long materials must be supported by a special bracket. When starting to cut, you must observe whether the incision is skewed, and you must stop immediately when it is found to be skewed to prevent the cutter or the grinding wheel from twisting and breaking and hurting people.