Fully automatic fiber laser cutting machine manufacturer for three-dimensional cutting

Automatic fiber laser cutting machine manufacturers follow to the cutting height, click on the laser, go up, take down the tape to see if the laser spot is in the center of the copper nozzle, if not, adjust the three screws (tighten clockwise to close, Loosen the far height) dimming spot Open the aluminum box, place the viewing lens between the half mirror and the beam expander, turn on the laser, then adjust the upper and lower two screws on the total mirror, the upper screw adjusts the up and down movement of the spot , Lower the screw to adjust the left and right movement of the light spot, loosen the anti-fixing before adjusting the light spot, move the light spot up, down, left and right to adjust the light spot to a relatively round and brighter spot, and then tighten the anti-fixing. The button function of the wireless handheld box F1 processing F2 stop F3 rising F4 tracking F5 positioning F6 border inspection F7 blowing F8 pause F9 backward F10 continue F11 laser adjustment follow the hand shape Auto key, automatically drop to the following height 0.8mm Down key: drop to the spindle Low point Up key: increase sensitivity height: fine-tune height step: disconnect the radio frequency cable D light is on Up side adjust the light (clockwise D light is off, counterclockwise light is on) when clockwise to D light just off, then turn counterclockwise When the D light turns on, go counterclockwise for an additional half turn. Connect the radio frequency cable, the hand-shaped Auto side adjust the follow height (0.8mm) clockwise follow the height 1 counterclockwise follow the height' and press the Auto button to see the follow height, repeat the adjustment until the follow height is 0.8mm, follow the adjustment method to remove the laser cutting Connect the head to the high-frequency line (the D light on the panel of the follower may be on at this time) adjust the internal disconnection protection adjustment capacitance of the follower (in the 2.5mm hole on the side of the follower near the dowm button) Note: disconnection protection adjustment method : Press the follow button to observe the cutting rise and fall, adjust the cutting head clockwise to fall, and counterclockwise to adjust the cutting head to rise until the cutting just rises. Follow the D light on the instrument to light up. After the D light is turned on, adjust it counterclockwise for another half circle) After the adjustment is completed, connect the high-frequency wire that has just been removed to the cutting head. 5. After the disconnection protection adjustment is completed, adjust the height adjustment capacitor: as shown in the figure below Note: The height adjustment capacitor adjustment method is roughly the same as the disconnection protection, and the high-frequency wire is connected After that, press the follow button to observe the cutting rise and fall, adjust the capacitance cutting head clockwise to rise, and counterclockwise to the original position of the machine. Maintenance process 1. Daily maintenance. Clean the residue at the bottom of the nozzle before going to work every day. Adjust the center to ensure that the laser is in the center of the nozzle, and look at the spot to ensure that the quality of the light is better. Adjust the follower to ensure the height during cutting.

Automatic fiber laser cutting machine manufacturers ensure the stability of cutting and perforation air pressure. , Use an air gun to blow the dust on the surface of the machine every day before leaving get off work to clean up the waste in the drawer. 2. Weekly maintenance 1. Blow clean the inside of the power box with an air gun. (Dust may cause poor contact of electronic components) 2. The filter in front of the water tank should be cleaned, and the internal dust should be blown down. Adjust the height of the capacitor so that the distance between the cutting head and the iron plate when following is 0.8mm, and all adjustments are completed In the future, the follower will be installed in the ranking of laser cutting machine manufacturers. According to a large number of early market research, combined with the industry characteristics of automotive sheet metal panels and chassis parts, the company is now launching a combination of industrial robots + fiber lasers for three-dimensional cutting. The total cost of consumables and electricity consumption is controlled within 20 yuan per hour, which completely and effectively solves the above problems. First, use industrial robots instead of five-axis machine tools. Both can describe the space trajectory to realize three-dimensional cutting. The repeat positioning accuracy of industrial robots is slightly lower than that of five-axis machine tools, about ±100uM, but this can fully meet the accuracy requirements of the automotive sheet metal panel and chassis parts industry. .

This article is published by the original