Fiber laser cutting machine is usually maintained to pay attention to incidents
The intelligent fiber laser cutting machine has the function of shortening the cutting time for users. Through the video head system on the cutting gantry, the Detection Eye can identify the exact position of the plate to be processed in just a few seconds. With the help of this active edge detection function, the preparation time of each fiber laser cutting machine's mission can be shrunk by 17 s. From high-precision inspection to high-precision cutting, accurate measurement of the very outer edge of the sheet (very very Large material utilization rate), can achieve accurate cutting results.
1. Fill the linear guide rail with lubricating oil
The fiber laser cutting machine uses smoke generated during a period of time, and the dust has corrosive use on the guide rail, so the guide rail should be maintained on schedule. Turn off the power of the fiber laser cutting structure, clean the guide rail with a clean soft cloth, and then drop smooth oil on the guide rail. After the oil is applied, let the slider roll back and forth on the guide rail to ensure that the smooth oil enters the slider. After oiling, let the slider roll back and forth on the guide rail. At this time, you must install the guide rail first. Be careful not to change it first when installing the guide rail. You must install all the unchanged nails, and the degree of connection is between the belt and the slider. No change, install the lens again, and adjust the light. The way to go is over.
2. Wiping mirror focusing mirror
After using fiber laser cutting machine|fiber laser cutting machine for a period of time, smoke and dust will adhere to the appearance of the lens, affecting the engraving and cutting depth , It will also affect the precision of engraving and cutting. Usually around one week (left card fiber laser cutting machine | frequency of engraving machine) use anhydrous alcohol to wipe the three mirrors and one focusing mirror thoroughly.
3. Bearing oiling
The fiber laser cutting machine uses a large number of bearings. In order to ensure superior cutting and engraving results, one-sided bearings need to be oiled on time (except oil-impregnated bearings) and clean Wipe off the floating soil on the bearing with a soft cloth, use a needle tube to suck the oil into the needle tube, and then use the needle to gradually inject the bearing, and then gradually roll the bearing when filling the oil.
4. Belt (transmission belt) tightness adjustment
There are geometric timing belts in the transmission system of the fiber laser cutting machine. If the timing belt is too loose, you will find ghosts in the engraved lettering. In the environment, if the timing belt is too tight, it will cause the timing belt to wear out. After using for a period of time, please adjust the tensioning screw of the timing belt to adjust the timing belt to the proper tightness. No ghosting can be found in the engraving pen and ink, and the running noise of the fiber laser cutting machine and fiber laser cutting machine is very low. You may consult the factory. Technical staff.
5. Maintenance of the laser tube
The laser tube in the fiber laser cutting machine is cooled by recurring water and will be used forever. There will be a little white scale in the tube. We can Probably a small batch of vinegar came in the reincarnation water, the ditch in the tube was removed, and then the laser tube was rinsed clean with clean water, so the laser tube would be in very good working condition and its life span would be extended.
The use of fiber laser cutting machine
The use of fiber laser cutting machine in our ordinary life is becoming more and more extensive, such as sinks, vacuum flasks, doors and windows, Kitchen and bathroom, office kitchen supplies and so on. What's the advantage of the laser fiber laser cutting machine stainless steel compared with the ancient stainless steel fiber laser cutting machine?
1. The speed of fiber laser cutting machine is rapid, the depth is large, and the deformation is small.
2. The process center of the fiber laser cutting machine generates very little heat, which can avoid the thermal deformation in the weld area< /p>
3. The surface of the fiber laser cutting machine is clean and the welding seam is of high quality. The overall appearance is without pores. The fiber laser cutting machine without too high request does not need polishing and polishing
4. It can be at room temperature Or the fiber laser cutting machine can be installed under special premises. The equipment assembly of the laser fiber laser cutting machine is simple
5. The fiber laser cutting machine can be used for refractory materials such as titanium, and can weld foreign materials with superior results
6. After the laser is focused, the power density is high. When the high-power device fiber laser cutting machine, the aspect ratio can reach 5:1, and the very high can reach 10:1
7. A miniature fiber laser cutting machine can be used. After the laser beam is focused, a small spot can be obtained, and the position can be cut and determined. It can be used in the assembly welding of micro and small workpieces that are automatically manufactured in large quantities.
8. It is very naive to perform non-touch and long-distance fiber laser cutting machine for parts that are difficult to approach by fiber laser cutting machine. Especially in recent years, optical fiber transmission technology has been adopted in YAG laser processing technology, so that laser welding has been widely promoted and used
9. The laser beam is easy to complete the beam splitting according to time and space. The ability to perform multi-beam simultaneous processing and multi-station processing provides a prerequisite for more stringent fiber laser cutting machines.