The noise problem of fiber laser cutting machine should be alleviated

If it is a slender workpiece, just take ninety degrees for cutting. In this way, the noise problem of the fiber laser cutting machine should be alleviated. In the past, we can understand the reasons for the noise of the automatic fiber laser cutting machine. There are many sources of noise in the fiber laser cutting machine, and there is no harm on the one hand. The vibration of the tool causes noise, and there is no harm to the guidance caused by the disadvantages of the process. In any case, the presence of noise does cause harm, so the noise of low-hanging machinery is also imperative.

After the historical analysis of the reasons, in order to avoid the disturbance of the fiber laser cutting machine due to noise, we must first select a reasonable tool and advance the accuracy of the device; at the same time Improve the cutting process of the fiber laser cutting machine.

The fiber laser cutting machine usually stops the cables being tied into bundles, stocked or shipped to another location in the factory. Bundling, or each end of the cable from the fiber laser cutting machine, can be bent and barbed. If it breaks in the fully automatic terminal crimping machine, then you need to adjust the tightness, debate the wheel, and briefly combine the terminal reel without expanding due to its weight. If the problem is in the binding process, you need to use a smaller fiber laser cutting machine or improve the handling method. The general installation of the terminal has special requirements: lower temperature -5°C, higher temperature 40°C. Many researches and comments have pointed out that the error rate of terminal blocks becomes an exponential climax with the touted temperature. The service life of the fiber laser cutting machine decreases exponentially with the touted temperature. The service life of the terminal blocks will be halved if the temperature is touted at 10°C.

The fiber laser cutting machine works fully automatically. It can cut the wire to a specified length and peel the two ends. At the same time, there are many models that enhance the results. Metaphor: support the middle Strip small windows, support twisting of multi-core wires, automatic splitting of cables, and layered stripping of wires with multilayer insulation, etc.; semi-automatic wire stripping machine requires manual control, which can effectively compensate for The blank of the automatic wire stripping machine can be used to process wires that cannot be realized by the automatic wire stripping machine. It is like a large-scale cable wire and the core wire of a sheathed wire.

Special requirements for fiber laser cutting machine: Fiber laser cutting machine usually stops the cable will be tied into bundles, stocked or shipped to another location in the factory. Bundled sales, or each end of the cable from the fiber laser cutting machine, can be bent and barbed. If it breaks in the fully automatic terminal crimping machine, then you need to adjust the tightness, debate the wheel, and briefly combine the terminal reel without expanding due to its weight. If the problem is in the binding process, you need to use a smaller fiber laser cutting machine or improve the handling method. The general installation of the terminal has special requirements: lower temperature -5°C, higher temperature 40°C. Many researches and comments have pointed out that the error rate of terminal blocks becomes an exponential climax with the touted temperature. The service life of the fiber laser cutting machine decreases exponentially with the touted temperature. The service life of the terminal blocks will be halved if the temperature is touted at 10°C.

Fiber laser cutting machine includes its electrical functions, material destructibility, temperature resistance, etc., which are higher than the secret requirements of ordinary fiber laser cutting, especially related to safety: Such as the direction control system and brake, these important parts of the fiber laser cutting machine require more stringent fiber laser cutting machines. The standard of fiber laser cutting machine disposal is mainly calculated by historical calculation of crimping rate. The calculation of the crimping rate requires special equipment and a unilateral standard tester for fiber laser cutting machines developed by the factory. The fiber laser cutting structure is used to test whether the crimping of the fiber laser cutting machine is qualified, short and long, and effective. detector.　The role of the automobile fiber laser cutting machine bundled in the vehicle is to transmit or exchange the power signal or data signal of the electrical system to achieve the results and requirements of the electrical system. It is the main body of the car circuit, and there is no wiring without a fiber laser cutting machine. The decision-making process and manufacturing process of automobile fiber laser cutting machine bundling are relatively cumbersome, and fiber laser cutting machine engineers are required to be cautious and not sloppy. If the decision of the fiber laser cutting machine is different and the results of each component cannot be combined, the fiber laser cutting machine is probably the most common unilateral aspect of car damage.